CCalclabhub

Math · 64 calculators

Coefficient Of Variation Calculator

The coefficient of variation measures spread relative to the size of the mean, so it lets you compare variability across data sets with very different units or scales. It is the standard deviation divided by the mean, normally reported as a percentage. This page explains the formula, shows how the squared CV and the relative standard error follow from it, and works through examples so you can use the measure with confidence.

Coefficient of variation

25.00%

Squared CV
0.0625
Relative standard error
0.05
Approximate range
60

Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.

The formula this calculator uses

CV = standard deviation / mean

CV
Coefficient of variation, the relative spread
sd
Standard deviation of the data
mean
Arithmetic mean of the data
n
Number of observations in the sample

How to check the result by hand

  1. 1

    Find the standard deviation and the mean

    The coefficient of variation needs two summaries of the same data: its standard deviation and its arithmetic mean. In the worked case these are supplied directly as 15 and 60. If you start from raw observations, compute the mean first and then the standard deviation, choosing the sample or population version consistently. Make sure both figures describe the same set and the same units.

  2. 2

    Divide the standard deviation by the mean

    Compute the raw ratio sd divided by mean. With 15 and 60 the result is 0.25. This is the coefficient of variation before any percentage is applied; the interface displays it as 25 percent because the output carries a percentage format, while the underlying number stays 0.25. Never insert a multiplication by 100 into the expression, or the displayed figure would be a hundred times too large.

  3. 3

    Square the CV for the variance ratio

    Multiply the raw CV by itself to get the dimensionless variance ratio. With a CV of 0.25 the squared value is 0.0625. This companion figure is useful in further algebra, since variances combine additively. It is a pure number with no units, and it will always be smaller than the CV whenever the CV is less than one.

  4. 4

    Divide by the square root of the sample size

    For the relative standard error, divide the raw CV by the square root of the number of observations. With 25 observations the square root is 5, and 0.25 divided by 5 gives 0.05. A larger sample makes this figure smaller, showing that the estimated CV is more precise. Always report the sample size next to a CV so readers can judge how much weight to give it.

  5. 5

    Estimate the approximate range and check direction

    Multiply the standard deviation by four to get a rough span for the bulk of the data: 4 times 15 is 60.0. Then sanity-check the direction of the main result. A larger standard deviation with the same mean must raise the CV, while a larger mean with the same spread must lower it. If your figure moves the other way, the two inputs have probably been swapped.

Common Questions

How does the Coefficient Of Variation Calculator work?

Divide the standard deviation by the mean to get the raw coefficient of variation. With a standard deviation of 15 and a mean of 60 the raw value is 0.25, which is displayed as 25 percent. Squaring it gives a dimensionless variance ratio of 0.0625, dividing by the square root of the 25 observations gives a relative standard error of 0.05, and four times the standard deviation gives an approximate range of 60.0.

What do I need to enter in the Coefficient Of Variation Calculator?

It takes 3 inputs: Standard deviation, Mean, Sample size. Fields that expect a unit say so next to the label.

Where does Coefficient of variation come from?

It comes from CV = sd / mean — the standard deviation divided by the mean. With sd equal to 15 and mean equal to 60 the raw ratio is 0.25, displayed as 25 percent.

What is the most common mistake with the Coefficient Of Variation Calculator?

Multiplying by 100 inside the expression. The output already carries a percentage format, so the renderer applies the scaling. Writing a multiplication by 100 in the expression makes the displayed figure a hundred times too large, turning 25 percent into 2,500 percent. Keep the raw decimal such as 0.25 in the formula and let the format handle the display.

For worked examples, common mistakes and the limits of this formula, read the full How To Calculate Coefficient Of Variation page.