Fluid Mechanics
How To Calculate The Reynolds Number
The Reynolds number is a single dimensionless value that predicts whether a fluid flow will be smooth and layered or chaotic and mixed. It compares the inertial forces that keep a fluid moving with the viscous forces that damp it down. Engineers use it to decide whether flow in a pipe, around a wing or past a ship hull will be laminar or turbulent, and to make small-scale models behave like the real thing.
Last updated
Quick Answer
Re = rho v L / mu
- Re
- Reynolds number (dimensionless)
- rho
- Fluid density, in kilograms per cubic metre
- v
- Flow speed, in metres per second
- L
- Characteristic length, in metres
- mu
- Dynamic viscosity, in pascal-seconds
Multiply the fluid density by its speed and a characteristic length, then divide by the dynamic viscosity. A low result means viscous forces dominate and the flow is laminar; a high result means inertia dominates and the flow is turbulent. For water with density 1,000 kilograms per cubic metre moving at 2 metres per second through a pipe 0.05 metres across, with viscosity 0.001 pascal-seconds, the Reynolds number is 100000.0.
What Is The Reynolds Number?
The Reynolds number is a dimensionless quantity that measures the relative importance of inertial forces and viscous forces in a moving fluid. It is named after Osborne Reynolds, who demonstrated in the nineteenth century that the same group of variables governs the transition from smooth to chaotic flow in pipes. Inertial forces are associated with the fluid's momentum and tend to keep it moving in its current path; viscous forces arise from internal friction and tend to smooth out differences in speed. The ratio of the two tells you which effect wins.
When the Reynolds number is small, viscosity dominates. Disturbances are damped out before they can grow, and the fluid moves in orderly parallel layers with little mixing between them. This is laminar flow, and it is what you see when honey pours slowly or smoke rises in a clean, straight column. When the Reynolds number is large, inertia dominates. Small disturbances grow rather than decay, the layers break down, and the flow becomes turbulent, with eddies and rapid mixing. Turbulent flow is what you see in a fast river or in the wake behind a moving vehicle.
For flow inside a circular pipe, transition from laminar to turbulent behaviour typically begins around a Reynolds number of 2,300. Below that value the flow is generally laminar, above about 4,000 it is generally turbulent, and the band in between is transitional and sensitive to disturbances such as vibrations or roughness at the pipe wall. These thresholds are empirical and depend on the geometry; the numbers quoted apply to pipe flow and should not be assumed for flow over a flat plate or around a sphere.
Each term in the expression has a clear physical role. Density rho sets how much mass the fluid packs into a given volume and therefore how strong its inertia is. Speed v sets how fast it is moving. Characteristic length L is a representative size of the geometry, such as the diameter of a pipe or the chord of a wing. Dynamic viscosity mu measures the fluid's internal resistance to shearing. A thick oil has a large viscosity and produces a small Reynolds number, while a thin gas has a small viscosity and produces a large one.
It is often convenient to combine density and viscosity into the kinematic viscosity, written as nu and defined as mu divided by rho. This quantity measures how readily momentum diffuses through the fluid and appears naturally when the governing equations are written per unit mass rather than per unit volume. Substituting it into the main expression gives the equivalent form Re equals v times L divided by nu. For the water in the worked example, dividing the viscosity of 0.001 pascal-seconds by the density of 1,000 kilograms per cubic metre gives a kinematic viscosity of 1e-06 square metres per second.
Two other quantities help interpret the inertial side of the balance. Dynamic pressure is one half of density times speed squared, and it represents the pressure rise that would occur if the flow were brought to rest; in the worked case it is 2000 pascals. Velocity head is the speed squared divided by twice the acceleration due to gravity, expressing the same kinetic energy as a height of fluid; with a speed of 2 metres per second it is about 0.2039 metres. Both grow with the square of speed, which is why doubling the flow speed has a much larger effect than doubling the density.
Because speed appears in the numerator, increasing the flow speed raises the Reynolds number in direct proportion: double the speed and you double the Reynolds number, other things being equal. Increasing the characteristic length has the same effect, which is why a large ship and a small model of it cannot both be turbulent at the same speed. Increasing the viscosity does the opposite and pushes the flow toward the laminar regime. This sensitivity is what makes the Reynolds number the natural parameter for comparing flows of different scales and different fluids.
The main application is dynamic similarity. If a scale model and the full-size object operate at the same Reynolds number, their flow patterns will be similar even if the fluids, speeds and sizes differ. Wind tunnels and towing tanks exploit this by adjusting speed or using a different fluid to match the Reynolds number of the real vehicle. The same reasoning appears in blood flow through arteries, in the design of pipelines and heat exchangers, in the aerodynamics of aircraft and in the study of sediment transport in rivers.
The number has limits that are worth keeping in view. The choice of characteristic length is a convention, and using a different one scales the answer, so you must state which length was used. Fluid properties, especially viscosity, change noticeably with temperature, so a value taken at one temperature may not apply at another. Surface roughness, pressure gradients and unsteadiness also influence transition, meaning the Reynolds number predicts the likely regime rather than guaranteeing it. Treat it as a powerful guide, not an absolute law.
Formula
Re = rho v L / mu
Formula page →The defining relation. Multiply density, speed and characteristic length, then divide by dynamic viscosity. All four quantities use consistent SI units so the result is dimensionless.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| rho | Fluid density | kg/m^3 | Mass per unit volume, in kilograms per cubic metre. |
| v | Flow speed | m/s | Mean speed of the fluid relative to the body. |
| L | Characteristic length | m | A representative dimension such as pipe diameter. |
| mu | Dynamic viscosity | Pa·s | The fluid's resistance to shearing, in pascal-seconds. |
nu = mu / rho
Formula page →Dynamic viscosity divided by density gives the kinematic viscosity, which allows the Reynolds number to be written as Re = v L / nu. For the worked water example this is 1e-06 square metres per second.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| nu | Kinematic viscosity | m^2/s | Momentum diffusivity of the fluid. |
| mu | Dynamic viscosity | Pa·s | The fluid's internal resistance to flow. |
| rho | Fluid density | kg/m^3 | Mass per unit volume. |
q = rho v^2 / 2, h = v^2 / (2 g)
Formula page →Dynamic pressure q is the pressure equivalent of the flow's kinetic energy, and velocity head h expresses the same energy as a fluid height using gravity g = 9.80665 metres per second squared. Both scale with the square of the speed.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| q | Dynamic pressure | Pa | One half of density times speed squared. |
| h | Velocity head | m | Speed squared divided by twice the acceleration due to gravity. |
| g | Acceleration due to gravity | m/s^2 | Standard value 9.80665 metres per second squared. |
How To Calculate The Reynolds Number
- 1
Gather the fluid properties
Write down the density rho in kilograms per cubic metre and the dynamic viscosity mu in pascal-seconds for the fluid at the temperature of interest. For water near room temperature these are about 1,000 and 0.001 respectively. Property values drift with temperature, especially viscosity, so use figures that match your conditions.
- 2
Choose the speed and characteristic length
Set the flow speed v in metres per second and pick a representative length L in metres, such as the diameter of a pipe or the chord of a wing. Make sure every quantity is in SI units before you start. Using millimetres for the length while keeping density and viscosity in SI units is a common way to get an answer a thousand times too large.
- 3
Optionally find the kinematic viscosity
Divide the dynamic viscosity by the density to get nu = mu / rho. This is not strictly necessary for the main calculation, but it is a useful cross-check and lets you use the alternative form Re = v L / nu. With the worked values, 0.001 divided by 1,000 gives a kinematic viscosity of 1e-06 square metres per second.
- 4
Compute the Reynolds number
Multiply density, speed and length, then divide by dynamic viscosity: Re = rho v L / mu. For the worked case that is 1,000 times 2 times 0.05, which is 100, divided by 0.001, giving 100000.0. The units cancel completely, so report a plain number with no unit attached.
- 5
Interpret the result and supporting quantities
Compare the value with the relevant transition threshold. In pipe flow, 100000.0 is well above about 4,000 and therefore firmly turbulent. You can also report the dynamic pressure, 0.5 rho v squared, which is 2000 pascals here, and the velocity head, v squared over 2g, which is about 0.2039 metres, to describe the inertial side of the balance.
Examples
Example 1: Water at 2 m/s in a 0.05 m pipe
- density
- 1000
- velocity
- 2
- length
- 0.05
- viscosity
- 0.001
| Step | Calculation | Result |
|---|---|---|
| Confirm SI units | 1000 kg/m^3, 2 m/s, 0.05 m, 0.001 Pa·s | SI units |
| Compute kinematic viscosity | 0.001 / 1000 | 1e-06 |
| Compute dynamic pressure | 0.5 x 1000 x 2 x 2 | 2000.0 |
| Compute velocity head | 2 x 2 / (2 x 9.80665) | 0.20394324259558566 |
| Compute the Reynolds number | 1000 x 2 x 0.05 / 0.001 | 100000.0 |
Result: The Reynolds number is 100000.0, well above the pipe-flow threshold and therefore turbulent, with kinematic viscosity 1e-06 m^2/s.
Example 2: A viscous oil moving slowly through a narrow tube
- density
- 900
- velocity
- 0.5
- length
- 0.02
- viscosity
- 0.1
| Step | Calculation | Result |
|---|---|---|
| Confirm SI units | 900 kg/m^3, 0.5 m/s, 0.02 m, 0.1 Pa·s | SI units |
| Compute kinematic viscosity | 0.1 / 900 | 0.00011111111111111112 |
| Compute dynamic pressure | 0.5 x 900 x 0.5 x 0.5 | 112.5 |
| Compute the Reynolds number | 900 x 0.5 x 0.02 / 0.1 | 90.0 |
Result: The Reynolds number is 90.0, far below the pipe-flow transition and therefore laminar, because the oil's high viscosity strongly damps the flow.
Example 3: Fast air flowing past a 0.5 m flat plate
- density
- 1.2
- velocity
- 20
- length
- 0.5
- viscosity
- 0.000018
| Step | Calculation | Result |
|---|---|---|
| Confirm SI units | 1.2 kg/m^3, 20 m/s, 0.5 m, 0.000018 Pa·s | SI units |
| Compute kinematic viscosity | 0.000018 / 1.2 | 1.5e-05 |
| Compute dynamic pressure | 0.5 x 1.2 x 20 x 20 | 240.0 |
| Compute the Reynolds number | 1.2 x 20 x 0.5 / 0.000018 | 666666.67 |
Result: The Reynolds number is 666666.67, so the airflow over the plate is strongly turbulent, a consequence of air's very low viscosity.
Calculator
Reynolds number
100,000
- Kinematic viscosity (m²/s)
- 0
- Dynamic pressure (Pa)
- 2,000
- Velocity head (m)
- 0.2039
Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.
Prefer a full-width tool? Open the The Reynolds Number calculator page.
Common Mistakes
Using inconsistent units
The expression assumes SI units throughout: kilograms per cubic metre, metres per second, metres and pascal-seconds. Entering the length in millimetres while leaving the other terms in SI units produces an answer a thousand times too large, and the dimensionless result will silently look plausible.
Confusing dynamic and kinematic viscosity
Dynamic viscosity mu carries units of pascal-seconds and belongs in the denominator of rho v L / mu. Kinematic viscosity nu is mu divided by density and belongs in v L / nu. Substituting one for the other without adjusting the density gives a badly wrong Reynolds number.
Applying pipe thresholds to other geometries
The familiar transition value near 2,300 applies to flow inside a circular pipe. Flow over a flat plate or around a sphere has a different critical Reynolds number. Carrying the pipe threshold over to a wing or a vehicle leads to the wrong regime being assumed.
Forgetting that viscosity depends on temperature
A fluid's viscosity can change substantially with temperature, particularly for liquids. Using a handbook value measured at a different temperature shifts the answer, and for liquids a warmer fluid is thinner, which raises the Reynolds number. Always state the temperature attached to your property values.
Choosing an arbitrary characteristic length
The Reynolds number scales with whichever length you pick, so comparing values that use different definitions is meaningless. A pipe is usually sized by its diameter and a wing by its chord. State the convention you used and keep it consistent when comparing cases.
Treating the result as an absolute prediction
The Reynolds number indicates the likely flow regime, but roughness, pressure gradients and incoming turbulence also affect transition. A flow just above the threshold may remain laminar in a very smooth, quiet setup. Use the number as a guide and allow for the borderline band.
FAQ
What does the Reynolds number actually tell you?
It compares inertial forces with viscous forces in a fluid. A low value means viscosity dominates and the flow is smooth and layered, while a high value means inertia dominates and the flow is chaotic and mixed. It therefore predicts the likely flow regime.
What Reynolds number marks the change from laminar to turbulent?
For flow inside a circular pipe, transition typically starts near 2,300 and the flow is usually fully turbulent above about 4,000. These are empirical figures for pipe flow; other shapes have different critical values.
Why is the Reynolds number dimensionless?
The units cancel exactly. Density in kilograms per cubic metre times speed in metres per second times length in metres gives kilograms per metre per second, which is precisely the unit of dynamic viscosity in the denominator. The ratio is therefore a pure number.
What is the difference between dynamic and kinematic viscosity?
Dynamic viscosity measures a fluid's internal resistance to shear and is used directly in the Reynolds number as mu. Kinematic viscosity is dynamic viscosity divided by density and lets the same number be written as v L over nu.
What is velocity head and why is it shown here?
Velocity head is the speed squared divided by twice the acceleration due to gravity. It expresses the kinetic energy of the flow as an equivalent height of fluid and, like dynamic pressure, grows with the square of speed, helping describe the inertial side of the balance.
How are Reynolds numbers used in scale models?
A model and a full-size object that operate at the same Reynolds number have dynamically similar flows. Wind tunnels and towing tanks adjust speed or fluid properties to match that number so measurements on a small model can be applied to the real vehicle.
References
- [1]Wikipedia, Reynolds number — https://en.wikipedia.org/wiki/Reynolds_number
- [2]Wikipedia, Viscosity — https://en.wikipedia.org/wiki/Viscosity
- [3]Wikipedia, Laminar flow — https://en.wikipedia.org/wiki/Laminar_flow
